开云体育

Yeah that overload is a problem for a lot of SDRs because the front ends are wide open so even a loud AM station by your house could overload the front end and mixing circuits making you think there

You should get audio well before max volume. I had my V12 Main Board and RF board working with my V11 LPF. It worked fine, and I made QSOs with it. - Jerry, KF6VB

Bill I got some BPF in place and I indeed have audio in headphones, volume at max. Slow pulsing I had is gone. So the RX path is working FB. I still get some random freeze ups but at least all is

Oh yeah… now I remember… it’s the reason I have a large building full of Standard AM/FM broadcast transmitters. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ

ATSC uses 8VSB modulation.

Hey yall' I think I found a player in the noise problem (maybe one of several!).? I had a very marginal power return connection that I corrected, not sure how this thing even worked with this

Must have been an FM system? That process would not work very well for SSB… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch –

That test software just tests to determine if the hardware is there and functioning… not for receiving and transmitting signals… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ

The system I worked on (ATSC) wasn't real time/continuous. The system took a snapshot of the RF, calculated then applied the corrections, then stopped. It could be set to run every X minutes, but

I see the sketch for testing board. I assume you load this into Teensy and plug BPF board into Boards Header? Not sure how I tell Teensy which band to activate. I am thinking? alternate maybe just

I presented the Right-Left Rule in the C Programming Guide book (1982) and there have been lots of examples written since then. This is a list of example you might use to test your understanding of

*** This reminds me of a project I've got on the back-burner. I got an amp that should be relatively decent. And a Boston Acoustics speaker mounted on the wall. Four HF rigs on the desk. I switch the

No problem… if you have amplified speakers or a stereo amp (audiophile or music)… I encourage you to use it. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner

THX Dr. Bill I was using headphones, only hear some clicking regular spaced noise, very suspicious Hi. Tim

Just so you are not misled here… the audio out from the main board needs to go to an external audio amp to hear stuff from a speaker. The output from the audio jack J14 (from the PCM5102) is about

I believe water fall was working in Jerry's just no signal in Filter Window Jack's beta both water fall and filter window is working FB. I have noticed that on startup the signal strength is initially

But does the waterfall work? Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa

I the next release it will be easy and intuitive instructions are on cal screen, easy peasy. Tim

I think audio is hardware I will check Daudio out on Tweensy to see if signal is there, if so then it is U5. I reloaded Jack's beta and it has working S meter and I see signal in filter window. I can

Interesting. I've got that software running on my V12 - working S meter and also audio out. - Jerry, KF6VB