开云体育

SUCCESS AT LAST!!!!!! After weeks of trying to figure out what I did wrong, my DDS VFO is working flawlessly and the increment problem has been solved. I replaced the rotary files downloaded from

OK guys, I managed to put everything together and so far is looking good. It powered up fine, so far I'm noticing that the encoder "step" function is not working when I push it down. It does move up

Am having some success making contacts with the 49-er transceiver this evening due to the SKCC Weekend Sprint contest going on at the moment. Just to clarify the setup on this end, the 49-er is taking

My apologies to the group. It appears this thread has be hijacked to continue the discussion about the hiss issue I'm having with my 49-er. I have some additional information but I'll put it out on

Thanks, Dave. Well... that's exactly what I'm using - a 12 volt gel cell. Heavy bugger but it's working great. The radio itself is working perfectly. The rotary encoder is tuning as it should. 40m is

Aaron,? I am using a 12 volt gel cell battery to power my 49er and I'm using Yamaha CM-500 headphones.? I don't know if the earbuds would make a difference or not, but as Jack just said, wall warts

Sorry... forgot to answer that question. I'm using a 12v, 8aH battery. It's the same one I use when I take my other rigs portable. Aaron - N2HTL On Sat, Apr 9, 2016 at 10:32 PM, Jack Purdum

I'll second Jack's recommendation on the Radio Shack solder.? That is all I use on circuit boards.? It is great stuff.? If I ever run out, I may have to quit the hobby. Dave. W0DF

I have a Jetstream 30A power supply with adjustable output voltage. I run it at 13.8V for my 100W rig, but 12V for my Forty-9er. Wall warts can be very noisy and so can some cheap 12V supplies. If you

I never use lead-free solder. I prefer 62/36/2 in a .022" diameter (2% silver). It melts like a dream at low temps. Radio Shack carried it, but it's getting tough to find. I found 7 spools on eBay and

First, download Farrukh's document: http://www.farrukhzia.com/k2zia/dds-vfo-assembly-manual-rev2.pdf and look at the encoder on the schematic: 'D' on the schematic is the data line, or DT. Now follow

What are you using to power the 49er with, battery, wall wart, 12 volt supply???

Hi Dave. Just disconnected the antenna and there's a lot of hiss on the output. Of course, the band is flooded with signals tonight due to the SKCC Weekend Sprint going on so it's much busier than it

I connect the 12V to J1; + to pins 1 or 2 and - to pins 3 or 4. Jack, W8TEE To: SoftwareControlledHamRadio@... Sent: Saturday, April 9, 2016 6:31 PM Subject: [SoftwareControlledHamRadio]

Aaron, What does the audio sound like with the antenna disconnected?? Are you hearing 40 meter band noise, or are you hearing audio hiss from within the 49er circuitry. I have one working and it does

Hello Norbert. I'm glad you found the solution. Was just about to respond when I read your latest post. Glad you got it resolved. I was wondering if you could do me a small favor. Once you power up

Got it, in finding some minor differences between the instructions in the QST and Farruk's link. I re-read the whole thing and page 22 on the QST instructions clearly states; "12V power for the

Never mind, I found the answer to my question while reading another post. For some reason I wasn't clear after reading the QST instructions, figure A11. Switch: Pin 17 Clock: Pin 22 (D3) Data: Pin 18

Thanks Jack. I just got back from out of town and will do it soon Dennis To: SoftwareControlledHamRadio@... From: SoftwareControlledHamRadio@... Date: Thu, 7 Apr 2016 20:11:35

Hi! Quick question, I see pins 2 and 4 in the diagram to power the VFO board and I already tried it when calibrating the mini360 5V output. My question is how do I power the 49er ? Does it feed from