开云体育

I received the V12 boards I am using back in June.? My Main board is labeled V12.6 while my RF board is labeled V12.06. I haven't seen any indication that there has been a new version of the RF board

Thanks! good to hear, I'm out the door going to work. Ron VE8RT "jjpurdum via groups.io" <jjpurdum@...> wrote:

Everything has been ordered. After reading the messages regarding display noise and 3.3 vs 5.0 volt options I ordered the 5.0 volt display. Ron VE8RT "Ron VE8RT" <ve8rt@...> wrote:

The Teensy 4.1 will work if it has the ethernet connector, it just costs a little more. The audio hat is for the Teensy 4.0 or 4.1 is fine. Jack, W8TEE

Quick question before I pay for my order, I found a couple of audio boards but this one seems to fit what I've found in the group messages. - its the T41 with the ethernet connector (the non ethernet

Here's the background for reference. This PJRC thread ( https://forum.pjrc.com/index.php?threads/teensy-4-1-cpu-heat-limits.65768/ ) discusses Teensy life vs clock speed/temperature.? It includes the

Install the following libraries via the Arduino Library Manager: * Adafruit MCP23017 Arduino Library, by Adafruit (v2.3.2) (note: install with dependencies) * Adafruit GFX Library, by Adafruit

Having problems adding this library: 21 | #include <LinearRegression.h> ? ? ?// https://github.com/cubiwan/Regressino/ | ? ? ? ? ?^~~~~~~~~~~~~~~~~~~~ compilation terminated. exit status 1

To avoid confusion from multiple in-development code versions flying around, I've made the github repository for the Version 63 code private. Al and Jack are actively working on the code, so that

Hi Everyone, I have attached the latest version of the T41 code. I believe it is in good shape but has yet to be thoroughly vetted. I am posting it now, ahead of a formal release to enable some of the

Follow Jack’s Advice… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand

Bill, what and where is the latest software? Roger G8JWT

Jack, it was from a post from several weeks ago GitHub Link <https://github.com/KI3P/SDTVer063>. Version 63-1 <https://github.com/KI3P/SDTVer063#version-63-1> This version of the code corresponds to

Where did that code come from? Jack, W8TEE

There’s a lot to that… I would suggest using the latest software version though… and start in the definitions section where the arrays are defined for the bands. Dr. William J. Schmidt - K9HZ

Its perfectly acceptable to wind turns over turns… Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois

I installed all of the required libraries and compiled this version. Looks good, but when I tried to do the Receiver Calibration, it worked like the directions(some of the switches were mapped

Thank you, I'll carry on, appreciate your saving me scanning over a year's of posts to the lists to check for recommended changes since my kit arrived. So wishing that I was retired already, I'll be

Your kit does not include the Teensy 4.1 or the Audio Hat, either (available from PJRC.com). The display is ordered from BuyDisplay.com and is a Chinese company so it will take some time. The correct

I was furtunate enough to received from Ron AG1P a T41 kit back in December of 2023. The plan to get to it in early 2024 didn't work out, I've just this last week gone through the box and have a good