¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
  1. SoftwareControlledHamRadio
  2. Messages
Expanded Topics Messages Polls
Date
Re: V12 compiling error

 

¿ªÔÆÌåÓý

Just so you are not misled here¡­ the audio out from the main board needs to go to an external audio amp to hear stuff from a speaker.? The output from the audio jack J14 (from the PCM5102) is about 2V maximum¡­? That may drive some high impedance headphones but not a speaker!

?

?

Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ

?

Owner - Operator

Big Signal Ranch ¨C K9ZC

Staunton, Illinois

?

Owner ¨C Operator

Villa Grand Piton ¨C J68HZ

Soufriere, St. Lucia W.I.

Rent it:

?

Moderator: North American QRO Group at Groups.IO.

Moderator: Amateur Radio Builders Group at Groups.IO.

?

email:? bill@...

?

?

From: [email protected] <[email protected]> On Behalf Of Tim via groups.io
Sent: Tuesday, February 11, 2025 10:35 AM
To: [email protected]
Subject: Re: [SoftwareControlledHamRadio] V12 compiling error

?

I think audio is hardware I will check Daudio out on Tweensy to see if signal is there, if so then it is U5.

I reloaded Jack's beta and it has working S meter and I see signal in filter window.

I can try reloading yours later.?

I loaded it using Tweensy Loader, could not quite figure out how do from Arduino IDE, as Dr. Bill says it may not be obvious.

You guys are great , last real programming I did was in 90's !?

The Arduino IDE keeps getting better I remember the days before the Library manager, much easier especially loading zip file from gethub!

Tim?
Re: V12 compiling error

 

I believe water fall was working in Jerry's just no signal in Filter Window
Jack's beta both water fall and filter window is working FB.?
?
I have noticed that on startup the signal strength is initially low and builds to reasonable level in a few seconds or so.
Might be AGC related.
?
Tim?
Re: V12 compiling error

 

¿ªÔÆÌåÓý

But does the waterfall work?

?

?

Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ

?

Owner - Operator

Big Signal Ranch ¨C K9ZC

Staunton, Illinois

?

Owner ¨C Operator

Villa Grand Piton ¨C J68HZ

Soufriere, St. Lucia W.I.

Rent it:

?

Moderator: North American QRO Group at Groups.IO.

Moderator: Amateur Radio Builders Group at Groups.IO.

?

email:? bill@...

?

?

From: [email protected] <[email protected]> On Behalf Of Tim via groups.io
Sent: Tuesday, February 11, 2025 10:16 AM
To: [email protected]
Subject: Re: [SoftwareControlledHamRadio] V12 compiling error

?

In Jacks Beta the S meter was working, this version the S meter is not , don't see a signal in filter window either.

Tim?

?
Re: Initial RX calibration not working

 

I the next release it will be easy and intuitive instructions are on cal screen, easy peasy.
Tim?
Re: V12 compiling error

 

I think audio is hardware I will check Daudio out on Tweensy to see if signal is there, if so then it is U5.
I reloaded Jack's beta and it has working S meter and I see signal in filter window.
I can try reloading yours later.?
I loaded it using Tweensy Loader, could not quite figure out how do from Arduino IDE, as Dr. Bill says it may not be obvious.
You guys are great , last real programming I did was in 90's !?
The Arduino IDE keeps getting better I remember the days before the Library manager, much easier especially loading zip file from gethub!
Tim?
Re: V12 compiling error

 

Interesting. I've got that software running on my V12 - working S meter
and also audio out.

- Jerry, KF6VB

On 2025-02-11 08:16, Tim via groups.io wrote:
In Jacks Beta the S meter was working, this version the S meter is not
, don't see a signal in filter window either.
Tim
Links:
------
[1] /g/SoftwareControlledHamRadio/message/32722
[2] /mt/111092895/243852
[3] /g/SoftwareControlledHamRadio/post
[4] /g/SoftwareControlledHamRadio/editsub/243852
[5]
/g/SoftwareControlledHamRadio/leave/10484476/243852/1943518115/xyzzy
Re: V12 compiling error

 

I have my T41 in pieces right now as I'm putting in a new LPF board and will be moving it to a new case. It will be tomorrow or the next day before I can check this.

Jack, W8TEE

On Tuesday, February 11, 2025 at 11:16:20 AM EST, Tim via groups.io <w4yn@...> wrote:


In Jacks Beta the S meter was working, this version the S meter is not , don't see a signal in filter window either.
Tim?
?

--
Jack, W8TEE
Re: V12 compiling error

 

In Jacks Beta the S meter was working, this version the S meter is not , don't see a signal in filter window either.
Tim?
?
Re: V12 compiling error

 

Loaded fine Jerry
Only issue now is I have no audio out, seems to be a hardware issue on my Main Board.
Tim?
Re: V12 compiling error

 

¿ªÔÆÌåÓý

You can, its just not obvious in the IDE¡­ but you can always load HEX code directly

?

?

Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ

?

Owner - Operator

Big Signal Ranch ¨C K9ZC

Staunton, Illinois

?

Owner ¨C Operator

Villa Grand Piton ¨C J68HZ

Soufriere, St. Lucia W.I.

Rent it:

?

Moderator: North American QRO Group at Groups.IO.

Moderator: Amateur Radio Builders Group at Groups.IO.

?

email:? bill@...

?

?

From: [email protected] <[email protected]> On Behalf Of Tim via groups.io
Sent: Tuesday, February 11, 2025 9:37 AM
To: [email protected]
Subject: Re: [SoftwareControlledHamRadio] V12 compiling error

?

Jerry?

That is a raw dump, I think, couldn't load in arduino progrmmer

Tim?
Re: V12 compiling error

 

It's a hex file. You should be able to upchuck it with the Teensy programmer.
It ( the programmer) has an "Open hex file" function in its command bar at the top. I sent it to you so you could just see if your radio worked, without
worrying about libraries or compile options.

- Jerry, KF6VB

On 2025-02-11 07:36, Tim via groups.io wrote:
Jerry
That is a raw dump, I think, couldn't load in arduino progrmmer
Tim
Links:
------
[1] /g/SoftwareControlledHamRadio/message/32718
[2] /mt/111092895/243852
[3] /g/SoftwareControlledHamRadio/post
[4] /g/SoftwareControlledHamRadio/editsub/243852
[5]
/g/SoftwareControlledHamRadio/leave/10484476/243852/1943518115/xyzzy
Re: V12 compiling error

 

Jerry?
That is a raw dump, I think, couldn't load in arduino progrmmer
Tim?
Fundamentals of I3C interface communication

 

! Wonder how soon we'll see devices that can handle it?
--
John P.
WA2FZW
Re: V12 compiling error

 

TNX Jerry I will compile and let you know.
I got my head around using Arduino programmer again.
Tend to for get if I sleep to many times Hi, 78 here.
Tim
Re: V12 compiling error

 

Yes RX cal works fine?
Will there be an option for different PB configurations?
My front panel designations are different than yours.
Tnx for all the help, Tim
Re: V12 compiling error

 

These look right, now. There's still a few things left for us to fix, but we're close.

Jack, W8TEE

On Monday, February 10, 2025 at 11:11:05 PM EST, Tim via groups.io <w4yn@...> wrote:


With smallest LTO
emory Usage on Teensy 4.1:
? FLASH: code:206376, data:127280, headers:8356 ? free for files:7784452
? ?RAM1: variables:178560, code:195720, padding:888 ? free for local variables:149120
? ?RAM2: variables:474752 ?free for malloc/new:49536

--
Jack, W8TEE
Re: V12 compiling error

 

With smallest LTO
emory Usage on Teensy 4.1:
? FLASH: code:206376, data:127280, headers:8356 ? free for files:7784452
? ?RAM1: variables:178560, code:195720, padding:888 ? free for local variables:149120
? ?RAM2: variables:474752 ?free for malloc/new:49536
Re: V12 compiling error

 

That's the right file. Did you optimize for smallest code with LTO? And you are using IDE 2.4.3?

Jack, W8TEE

On Monday, February 10, 2025 at 04:21:18 PM EST, Tim via groups.io <w4yn@...> wrote:


I got the beta V063-1-2 running and staying up now, not sure what I did different.
My PB's are not what they were before Probably need different menu file?
I noticed that Calibrate RX is way wonky doesn't look at all correct.
But it is running I moved fan around maybe that helped I don't have back on case fan is just positioned near Tweensy?
Temp says 42 degrees C
Tim?

--
Jack, W8TEE
Re: Initial RX calibration not working

 

Apparently I've missed the write-up on the V12 receive calibration that Tim is referring to.
Any chance that someone can point me to where I can find it as well as the latest software
version that he is using.? I haven't been able to keep up with all the changes and I admit
to getting confused (old age??) when messages refer to software or other documentation
without a specific reference.
?
Thanks so much!
Steve
K8ZBE
Re: Rob Sherwood Presentation Slides on Amateur Radio Transceiver Performance

 

Yes Pure Signal is open. Go take a look at Thetis for the Anan or Hermes/Hermes Lite radio.
?
My simplistic thinking is that it works a bit like noise cancelling headphones, except the thing cancelled is the noise (distortion) added to the signal by the Tx chain not the external noise.
?
Delay in the Tx chain exists but I don't think that stops the predistortion from cancelling IMD. The IMD created in the chain for a given input to the chain should be deterministic and repeatable.
?
On Mon, Feb 10, 2025 at 03:33 PM, Greg KF5N wrote:

You can do negative feedback.? But there has to be a phase adjustment so the system is stable.
?
I thought the "Pure Signal" pre-distortion software was open source?
?
--
73 Greg KF5N
1281 - 1300 of 33859