¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Date
Calibrate S meter?
I was just doing this for one of my other radios, and wondered: Is the S meter display on the T41 calibrated? S9 is defined as -73dBm, or 50 microvolts @ 50 ohms. I think I'll try it out with a signal
By jerry-KF6VB · #32642 ·
Re: [AmateurRadioBuilders] V12 RF Board
That is on the ¡°TO DO¡± list. Since this is an open/ community project¡­ I would ask that someone with a working radio¡­ please step up¡­ do this as a contribution to the project if¡­ people
By K9HZ · #32641 ·
Re: Excessive Noise
I¡¯ve never had noise from an on-board source, but that doesn¡¯t mean it couldn¡¯t happen. There is probably a solder bridge somewhere that is causing this¡­ but keep it simple¡­ to hone in on
By K9HZ · #32640 ·
Re: Excessive Noise
Should be 60db of attenuation
By epif18@... · #32639 ·
Re: Excessive Noise
Thanks Bill, that sounds like a plan.? I just finished hooking up my sig gen to one of the antenna with an output of -40dbm and 60dbm of attenuation, 7MHz AM, RF gain set at 0 and I could see and
By epif18@... · #32638 ·
Re: Excessive Noise
Mark¡­. You can unplug everything except the MAIN and RF boards (and the front panel and encoders) and the radio should work by just placing a receive antenna on the RX IN on the RF board. If you
By K9HZ · #32637 ·
Re: Excessive Noise
Hey Tim, Not yet.? I was tracing all the paths on the LPF control board to make sure I didn't have a problem with one of those 0179's.? I found a problem with the SWR xfmr in the tx path, so I fixed
By epif18@... · #32636 ·
Re: Initial RX calibration not working
Put it into receive calibration mode and check a few things: 1) Do you see clock signals at the expected frequency on the clock lines? 2) Do you see the receive calibration tone at the RF in SMA
By Oliver KI3P · #32635 ·
Initial RX calibration not working
V12 board set 50.2 FW Jumper J4 in place I select RX calibration and never see the signal on display, tried lowering attenuation no help Press the menu button to show signal from oscillator and it
By Tim · #32634 ·
Re: Excessive Noise
Mark did that help I am trying to calibrate and all I see on spectrum scope is noise Changing frequency does not change spectrum or water fall. Tim
By Tim · #32633 ·
Re: Display driver board reality
Also for the 5" version... Regards Phil VK2KKZ
By Phil Taylor · #32632 ·
Re: Display Driver 3.3V ONLY board
Hang tight¡­ I still have kit parts coming in from overseas¡­ and I want to send a couple of these out to folks I know will pound on them to see if there are any holes to fill. Dr. William J.
By K9HZ · #32631 ·
Re: Display Driver 3.3V ONLY board
How to order?? Jack, W8TEE
By jjpurdum · #32630 ·
Re: Show and Tell Friday #1
Bill, how about alink to where this is on GitHub? Not building the T41, but this might be useful for some of my other projects. Also where to get the encoder? -- John P. WA2FZW
By John P · #32629 ·
Re: Teensy 4.1 NE vs Ethernet
Thanks!
By bruce williams · #32628 ·
Re: Display Driver 3.3V ONLY board
Wow, looks nice!
By bruce williams · #32627 ·
Display Driver 3.3V ONLY board
Another Friday share¡­ The new Display Driver board. This is the 3.3V ONLY board. It¡¯s the cheaper of the two options. Use it of you don¡¯t (and won¡¯t) use 5V to power your display (if you will
By K9HZ · #32626 ·
Show and Tell Friday #1
Just some Friday sharing¡­ Here is a finished dual encoder board with 3D Printed knobs (all out on the GITHUB). Replaced TWO encoders. One ribbon cable from the encoder board to the Fron Panel
By K9HZ · #32625 ·
Re: Display driver board reality
For that display¡­ yes. Dr. William J. Schmidt - K9HZ J68HZ 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch ¨C K9ZC Staunton, Illinois Owner ¨C Operator Villa Grand
By K9HZ · #32624 ·
Re: Display driver board reality
Well here are the logic levels in the Spec sheet VDDIO is clearly 3.3V, Max voltage 3.6. VDDIO Hi and 0.2VDDIO Low. Regards Phil VK2KKZ
By Phil Taylor · #32623 ·