开云体育

Then we are fine. Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand

The LPF control cable connects to the “BANDS” connector on the MAIN board, J12…. and to the “BANDS” connector on the LPF Control board J21. It should be on on WIRE2 at hex address x25 which

Can you describe how you found this bug in more detail? i.e., what specific buttons you pressed and in what order. If your radio seems to be in an unrecoverable state, you may need to reset the flash.

Soldering JP2 while leaving JP1 and JP3 open makes the address bits 101 (they are high by default and soldering the junction pulls them to ground). This should correspond to the address 0x25, as you

My point was that I’m in that “Give Back” part of my life to support this hobby, and I talk about it to inspire other to do the same.? But evidently that struck a sour chord with you.. so

Finished building the LPF Control board, no detectable shorts or opens and no smoke escaped. The board is configured for I2C addressing and the address jumpers are set for address "25"(Open, Short,

Hi Justin. Thank you for the information.? I'll move forward with the build. Duane - K5CA

Hi Steve: You're right...and in some cases, those interests change over time. I ran 500W from about 1972 to 1990's and then went to a "standard" 100W transceiver. When I retired in 2009, I discovered

The point missed here is that our hobby survives by bringing new people into the hobby and helping them to flourish in whatever avenue keeps them interested (building, operating, POTA, Digital Modes,

Hey Duane, The 0R resistors are correct. When I sent my boards to fabrication 3.3K resistors were in the schematic but this was changed shortly afterward. There was some discussion in this group that

Will do. Thanks. Duane - K5CA

All One of the great things about this hobby of amateur radio is that is has so many different aspects that interest just about anyone. I became interested in amateur radio twenty years ago. I ended

Like I said, you are a big contester and, while much more modest equipment, I enjoy contesting, too. I'm just not very good at it. I've participated in Field Day, the Sweepstakes, and several QRP

Completed RX and TX IQ cal all working fine. I went into menu to change display options, as soon as menu came up it returned went back to spectrum display which was only partial display. Now it

You are gonna have to ask Justin why he did that… Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton,

I started out contesting when I was 15… like all my friends and most of the contesters today. The first contest I ever entered was a novice round-up. and I only made about 25 contacts because the

Hi.? I purchased a set of boards from Justin, AI6YM.? I working on putting the RF module/board.? Looking at the schematic, it reads that R35 and R37 are supposed to be 3.3KΩ.? Looking at the

I've submitted scores to contests, too, and I can understand interest in where you placed. However, I think listing the top, say, 25, in each category would be enough. The complete listing could have

Certainly no more than the thousands of people that participate in them and submit their scores… Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner -

When it came to contest scores, I think CQ was the worst offender.? I found it hard to believe more than a handful of people would care about all of the scores in all of the contests. Jack, W8TEE