开云体育

Interference between two AN/SC with wireless handpad

贵谤é诲é谤颈肠 Ruciak All Messages By This Member #6423 Hi all, last may I participated to the "Rencontres Astronomiques du Printemps" so called , a star party near Le Puy en Velay in France. I set up my UC 22 near a very original telescope a 910mm diameter one with primary made of two meniscus spaced by a series of glass spacers everything fusioned at high temperature (see picture of the secondary on the same design). Once again I had the pleasure to enjoy a clear darksky (1100m altitude with all city light shut down for 3 nights) and wonderful views to share thank to my UC #1 AN/SC supercharge with some mods (dismountable primary stray light box and linear air flow to cool the primary). My neighbour and I both had AN/SC and wireless handpad and were located some 7 to 10 meters apart. I had continuously some strange behaviours of my scope that I first suspected were related to some slipping altitude cable and my neighbour had some issues too. I checked everything the next day but everything was ok but I had the same problems again the following night. I had to leave and my neighbour stayed alone the last night and he experienced no problem anymore. So I deeply suspect that our wireless handpads were interfering, SC 1 taking order or wireless HP 2 and vice versa. Did anyone experience the same king of issues previously? is there any way to get around except than moving 20m or more away from anyother Wireless handpad? Thank you for your advice. 贵谤é诲é谤颈肠 .
Richard All Messages By This Member #6424 开云体育 You can change the dip switches to avoid interference on my wireless hand pad. Richard Miller 33.51N 83.59W UC18 & DS287m toggle quoted message Show quoted text From: [email protected] <[email protected]> on behalf of 贵谤é诲é谤颈肠 Ruciak <frederic.ruciak@...> Sent: Tuesday, August 23, 2022 7:17:35 AM To: [email protected] <[email protected]> Subject: [ServoCAT] Interference between two AN/SC with wireless handpad ? Hi all, last may I participated to the "Rencontres Astronomiques du Printemps" so called , a star party near Le Puy en Velay in France. I set up my UC 22 near a very original telescope a 910mm diameter one with primary made of two meniscus spaced by a series of glass spacers everything fusioned at high temperature (see picture of the secondary on the same design). Once again I had the pleasure to enjoy a clear darksky (1100m altitude with all city light shut down for 3 nights) and wonderful views to share thank to my UC #1 AN/SC supercharge with some mods (dismountable primary stray light box and linear air flow to cool the primary). My neighbour and I both had AN/SC and wireless handpad and were located some 7 to 10 meters apart. I had continuously some strange behaviours of my scope that I first suspected were related to some slipping altitude cable and my neighbour had some issues too. I checked everything the next day but everything was ok but I had the same problems again the following night. I had to leave and my neighbour stayed alone the last night and he experienced no problem anymore. So I deeply suspect that our wireless handpads were interfering, SC 1 taking order or wireless HP 2 and vice versa. Did anyone experience the same king of issues previously? is there any way to get around except than moving 20m or more away from anyother Wireless handpad? Thank you for your advice. 贵谤é诲é谤颈肠 .
K9RX - Gary All Messages By This Member #6425 Frederic, Contact me direct and we can discuss what to look for re the ALT axis 'slipping'.? As for the wireless. You mention "HP 2" ... not sure if you were saying this is a Gen2 ServoCAT system or not. The Gen2 wired and wireless HP's had only 5 buttons on them and a tiny slide switch. If that is what you have then note there are jumpers inside the HP's and internal to the ServoCAT that change the address of the system. They do not change the frequency - only an address so interference is still possible but this will help. Note all 3: ServoCAT, wired and wireless HP's all have to have the same jumper settings. To further reduce the likelihood of interference one can reduce the height/extension of the base units extendible antenna just to where it works locally with the handpad. This coupled with the address change should work fine.? If this is a Gen3 you can change the channel used.? Gary Myers StellarCAT
贵谤é诲é谤颈肠 Ruciak All Messages By This Member #6426 Hi Gary my wireless HP is definitely this one ?in the picture, so most probably a Generation 3. Is there somewhere in the manual indicating how to change the channel? If yes I most probably missed it. Thank you for your help. Clear skies Frederic
K9RX - Gary All Messages By This Member #6427 The instructions on how to change the channel were included in each box with each unit. The instructions for the base unit being slightly different from the HC unit. I'll send you a copy of it directly (also these docs are on the CD as well). Gary? toggle quoted message Show quoted text ------ Original Message ------ From "贵谤é诲é谤颈肠 Ruciak" <frederic.ruciak@...> To [email protected] Date 8/26/2022 2:17:20 AM Subject Re: [ServoCAT] Interference between two AN/SC with wireless handpad Hi Gary my wireless HP is definitely this one ?in the picture, so most probably a Generation 3. Is there somewhere in the manual indicating how to change the channel? If yes I most probably missed it. Thank you for your help. Clear skies Frederic
贵谤é诲é谤颈肠 Ruciak All Messages By This Member #6428 Hi Gary,? thanks for you reply but I have to say that having received it completely installed from Obsession, I do not have "the instructions included in the box with each unit" that you refer to. If you have a pdf version of it, it would be wonderful. Thanks in advance, 贵谤é诲é谤颈肠
K9RX - Gary All Messages By This Member #6429 We ship the wireless (and wired) HC's in their individual boxes - and instructions are in those boxes. OEM's are suppose to send you that.? The docs are on the CD under "Manuals/Other Instructions" and I sent them to you using the email address I have here - it came back with a fatal non-delivery notice.? Gary? toggle quoted message Show quoted text ------ Original Message ------ From "贵谤é诲é谤颈肠 Ruciak" <frederic.ruciak@...> To [email protected] Date 8/26/2022 9:35:43 AM Subject Re: [ServoCAT] Interference between two AN/SC with wireless handpad Hi Gary,? thanks for you reply but I have to say that having received it completely installed from Obsession, I do not have "the instructions included in the box with each unit" that you refer to. If you have a pdf version of it, it would be wonderful. Thanks in advance, 贵谤é诲é谤颈肠
贵谤é诲é谤颈肠 Ruciak All Messages By This Member #6430 On Fri, Aug 26, 2022 at 03:54 PM, K9RX - Gary wrote: We ship the wireless (and wired) HC's in their individual boxes - and instructions are in those boxes. OEM's are suppose to send you that.? ? The docs are on the CD under "Manuals/Other Instructions" ? and I sent them to you using the email address I have here - it came back with a fatal non-delivery notice.? ? Gary? ? ? ? ? ------ Original Message ------ From "贵谤é诲é谤颈肠 Ruciak" <frederic.ruciak@...> To [email protected] Date 8/26/2022 9:35:43 AM Subject Re: [ServoCAT] Interference between two AN/SC with wireless handpad ? Hi Gary,? thanks for you reply but I have to say that having received it completely installed from Obsession, I do not have "the instructions included in the box with each unit" that you refer to. If you have a pdf version of it, it would be wonderful. Thanks in advance, 贵谤é诲é谤颈肠 ?Hi Gary sorry if you still have the @bbox.fr address can you retry with frederic.ruciak@.... Thanks again and clear skies. 贵谤é诲é谤颈肠

Previous Topic Next Topic