¿ªÔÆÌåÓý

ctrl + shift + ? for shortcuts
© 2025 Groups.io
Re: How to get the .dat file of my servocat Version V60E ?
Hi Rapha?l. You should contact Normand at Optiques Fullum. He may have a record of your settings. I do not believe you will be able to download them from your device. If you want a copy of the latest
How to get the .dat file of my servocat Version V60E ?
Dear all, I'm Rapha?l, a french astronomer owing a Fullum scope I have Argonavis version 2 and servocat V60E I want to update both firmware to be able to follow satellites. But I don't have the
By Raphael Guinamard · #6756 ·
Re: Coiled extension cables for ServoCAT hand pads.
Mike: If you are in a shed with a long hand controller cable, how will you manage cable wrap around the telescope? BC
By Bill Conrad · #6755 ·
Re: Coiled extension cables for ServoCAT hand pads.
Hi Bill, I am in the process of building a small shed to set up next to my Obsession and would like to be able to use the hand control there rather than using a CATPaw. ?The uncoiled cable would be a
By mm Bars · #6754 ·
Re: Coiled extension cables for ServoCAT hand pads.
Hi Mike: You can connect two coiled cables together using a 4P4C coupling. You would need to use a meter to insure that the coupling maintains the same end-to-end wiring pattern. But how long of a
Coiled extension cables for ServoCAT hand pads.
My question is regarding the coiled cables for the hand-pad. ?Can 2 coiled cables be linked together? ?If so, would a special connected be required? Thanks, Mike
By mm Bars · #6752 ·
Re: Plate solving with ServoCAT and an alternative approach
Hi to Spectroscopy Group members. Re: selecting a suitable guide star when collecting spectra in a sparce star field. Hampshire Astro Group often find it difficult to identify a chosen star when
By alan.g.fowler@... · #6751 ·
Re: Plate solving with ServoCAT
Paul, I now understand. I could do it that way as I use a stand attached to my dob that holds a 15" laptop. The issue I ran into no matter is that Nexus didn't have a way to communicate with Peter or
By Mickey Huffman · #6750 ·
Re: Plate solving with ServoCAT
Mickey, I am not exactly sure what you are asking but I can explain my set up. I have a Dob with a ServoCat version 3 and the AN.? The AN connects to the SC through the AN serial port and the SC
By Paul Abel · #6749 ·
Re: Gary: please advise¡­Runnaway Alt. servo-motor
Hi Gary: Not the dsc, it was not connected. I will talk to Bill. Best Regards, Tim
By Tim Harris · #6748 ·
Re: Gary: please advise¡­Runnaway Alt. servo-motor
Tim, There are two potential causes of what you describe. First some background. When I decided to design the ServoCAT I needed a DSC to 'talk to' ... and as it turns out the Sky Commander had a
By K9RX - Gary · #6747 ·
Re: Gary: please advise¡­Runnaway Alt. servo-motor
Good Morning Gary: I am having a servo issue, the servo will runaway, I can get it to stop with the hand pad.? It will also make short move ( about half a turn on the servo output shaft) about every
By Tim Harris · #6746 ·
Re: Wireless handpad
Accessories servocat.comScroll through accessories to find it. Mickey
By Mickey Huffman · #6745 ·
Re: Wireless handpad
I t would something like this sitting on top of or attached in someway to the main unit.
By Mickey Huffman · #6744 ·
Re: Wireless handpad
I do not know what that is.
By Larry Gauerke · #6743 ·
Re: Plate solving with ServoCAT
Hi Hugo, You should be able to connect via ASCOM to test connectivity. Are you sure com3 is correct? You should go into device manager and see what com port is being used by servocat and then make
By Mike · #6742 ·
Re: Plate solving with ServoCAT
Is anyone using dobs and having success with this Sharpcap method of going thru the planetarium computer (argo nav) or (nexus)? If so how? I know of no way to connect directly to servocat with a
By Mickey Huffman · #6741 ·
Re: Wireless handpad
Do you have the remote antenna that is for receiving the signal from the wireless handpad?
By Mickey Huffman · #6740 ·
Wireless handpad
I bought a wireless handpad with my Gen 2 Servocat system. It has not been used in a very long time. Think pre-covid. I have replaced the battery on it and now the lights come on, but it does not do
By Larry Gauerke · #6739 ·
Re: Plate solving with ServoCAT
Hi Mike from Virginia, Very interested in your results it got me trying to do the same. I have a question for you. When you connect your PC via USB to the ServoCAT box with the Peter Eschman Driver,
By hbrunet181@... · #6738 ·