|
I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
|
Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps.
On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
|
Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck?
toggle quoted message
Show quoted text
-sent from my iphone --
On Jan 13, 2022, at 11:13 PM, Stan ... <alaska.stan@...> wrote:
? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
|
Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan
On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
|
? ? Hi Stan,
I understand what you¡¯re saying.?
I just ordered a THC module from Cnc4PC.com, model THC-2.
??It¡¯s compatible with the artsoft Mach3 plasma post processor. ?
Unfortunately I have no LUA Knowledge.?
Thanks, Chuck
toggle quoted message
Show quoted text
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
? Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
Attachments:
|
Stan,
Would you please post a sample? of your G-code?
I would like to compare it to the post processed G code using the Artsoft Plasma post processor. Thanks, Chuck
toggle quoted message
Show quoted text
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
? Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
Attachments:
|
I did... it is a jpg attachment
On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler < chuck767@...> wrote: Stan,
Would you please post a sample? of your G-code?
I would like to compare it to the post processed G code using the Artsoft Plasma post processor. Thanks, Chuck ? Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
Attachments:
|
Thanks Stan, Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck
toggle quoted message
Show quoted text
-sent from my iphone --
On Jan 16, 2022, at 9:23 PM, Stan ... <alaska.stan@...> wrote:
? I did... it is a jpg attachment On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler < chuck767@...> wrote: Stan,
Would you please post a sample? of your G-code?
I would like to compare it to the post processed G code using the Artsoft Plasma post processor. Thanks, Chuck ? Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
Attachments:
|
Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-)
On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler < chuck767@...> wrote: Thanks Stan, Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck ? I did... it is a jpg attachment On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler < chuck767@...> wrote: Stan,
Would you please post a sample? of your G-code?
I would like to compare it to the post processed G code using the Artsoft Plasma post processor. Thanks, Chuck ? Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
Attachments:
|
Thanks for the info, ?because of other commitments I will not be installing my THC system for about a month, but I will report back To the group on how this set up works.
toggle quoted message
Show quoted text
-sent from my iphone --
On Jan 16, 2022, at 10:52 PM, Stan ... <alaska.stan@...> wrote:
? Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-) On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler < chuck767@...> wrote: Thanks Stan, Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck ? I did... it is a jpg attachment On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler < chuck767@...> wrote: Stan,
Would you please post a sample? of your G-code?
I would like to compare it to the post processed G code using the Artsoft Plasma post processor. Thanks, Chuck ? Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful. Stan On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler < chuck767@...> wrote: Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor? Chuck? ? Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps. On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler < chuck767@...> wrote: I recently attached by plasma torch to my milling machine.
?
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.?
Going this route I am using a lot of consumables on the plasma torch.?
I¡¯m interested in using the MACH3 plasma profile With the torch height control, ?THC, Provisions.
?
Can someone point me in the right direction to get this set up??
thank you,
Chuck
?
Attachments:
|
On Mon, Jan 17, 2022 at 2:45 AM Chuck Kahler <chuck767@...> wrote:
Thanks for the info, because of other commitments I will not be installing my THC system for about a month, but I will report back To the group on how this set up works.
Hmmm - - - which THC system did you install? Would also be curious as to the actual plasma system your working with. (I really want a decent sized plasma torch and buying a system from the big boys is out of reach ($$$$$) - - - so wondering - - - ) TIA
-sent from my iphone --
On Jan 16, 2022, at 10:52 PM, Stan ... <alaska.stan@...> wrote:
?
Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-)
On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler <chuck767@...> wrote:
Thanks Stan,
Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck
-sent from my iphone --
On Jan 16, 2022, at 9:23 PM, Stan ... <alaska.stan@...> wrote:
?
I did... it is a jpg attachment
On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler <chuck767@...> wrote:
Stan,
Would you please post a sample
of your G-code
I would like to compare it to the post processed G code using the Artsoft Plasma post processor.
Thanks,
Chuck
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
?
Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful.
Stan
On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler <chuck767@...> wrote:
Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor?
Chuck
-sent from my iphone --
On Jan 13, 2022, at 11:13 PM, Stan ... <alaska.stan@...> wrote:
?
Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps.
Stan
On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler <chuck767@...> wrote:
I recently attached by plasma torch to my milling machine.
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.
Going this route I am using a lot of consumables on the plasma torch.
I¡¯m interested in using the MACH3 plasma profile With the torch height control, THC, Provisions.
Can someone point me in the right direction to get this set up?
thank you,
Chuck
Attachments:
20220114_122145.jpg
|
I have a CandCNC THC system and a Cutmaster A60 plasma torch I would like to sell...
toggle quoted message
Show quoted text
On 1/17/2022 4:18 AM, o1bigtenor wrote: On Mon, Jan 17, 2022 at 2:45 AM Chuck Kahler <chuck767@...> wrote:
Thanks for the info, because of other commitments I will not be installing my THC system for about a month, but I will report back To the group on how this set up works. Hmmm - - - which THC system did you install?
Would also be curious as to the actual plasma system your working with.
(I really want a decent sized plasma torch and buying a system from
the big boys is out of reach ($$$$$) - - - so wondering - - - )
TIA
-sent from my iphone --
On Jan 16, 2022, at 10:52 PM, Stan ... <alaska.stan@...> wrote:
?
Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-)
On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler <chuck767@...> wrote:
Thanks Stan,
Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck
-sent from my iphone --
On Jan 16, 2022, at 9:23 PM, Stan ... <alaska.stan@...> wrote:
?
I did... it is a jpg attachment
On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler <chuck767@...> wrote:
Stan,
Would you please post a sample
of your G-code
I would like to compare it to the post processed G code using the Artsoft Plasma post processor.
Thanks,
Chuck
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
?
Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful.
Stan
On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler <chuck767@...> wrote:
Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor?
Chuck
-sent from my iphone --
On Jan 13, 2022, at 11:13 PM, Stan ... <alaska.stan@...> wrote:
?
Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps.
Stan
On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler <chuck767@...> wrote:
I recently attached by plasma torch to my milling machine.
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.
Going this route I am using a lot of consumables on the plasma torch.
I¡¯m interested in using the MACH3 plasma profile With the torch height control, THC, Provisions.
Can someone point me in the right direction to get this set up?
thank you,
Chuck
Attachments:
20220114_122145.jpg
|
I will be using the ¡°THC ¨C2¡± Controller from cnc4pc.com
I simply built a quick release adapter to hold my plasma torch on my 15 x 30¡± travel milling machine.
This machine also has a 180 W CO2 laser attached to it, so it¡¯s an all purpose milling, laser cutting, plasma cutting machine for relatively small parts.
toggle quoted message
Show quoted text
-sent from my iphone -- On Jan 17, 2022, at 4:18 AM, o1bigtenor <o1bigtenor@...> wrote:
?On Mon, Jan 17, 2022 at 2:45 AM Chuck Kahler <chuck767@...> wrote:
Thanks for the info, because of other commitments I will not be installing my THC system for about a month, but I will report back To the group on how this set up works.
Hmmm - - - which THC system did you install?
Would also be curious as to the actual plasma system your working with.
(I really want a decent sized plasma torch and buying a system from
the big boys is out of reach ($$$$$) - - - so wondering - - - )
TIA
-sent from my iphone --
On Jan 16, 2022, at 10:52 PM, Stan ... <alaska.stan@...> wrote:
?
Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-)
On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler <chuck767@...> wrote:
Thanks Stan,
Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck
-sent from my iphone --
On Jan 16, 2022, at 9:23 PM, Stan ... <alaska.stan@...> wrote: ?
I did... it is a jpg attachment
On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler <chuck767@...> wrote:
Stan,
Would you please post a sample
of your G-code
I would like to compare it to the post processed G code using the Artsoft Plasma post processor.
Thanks,
Chuck
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
?
Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful.
Stan
On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler <chuck767@...> wrote:
Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor?
Chuck
-sent from my iphone --
On Jan 13, 2022, at 11:13 PM, Stan ... <alaska.stan@...> wrote:
?
Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps.
Stan
On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler <chuck767@...> wrote:
I recently attached by plasma torch to my milling machine.
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.
Going this route I am using a lot of consumables on the plasma torch.
I¡¯m interested in using the MACH3 plasma profile With the torch height control, THC, Provisions.
Can someone point me in the right direction to get this set up?
thank you,
Chuck
Attachments:
20220114_122145.jpg
|
What is the 180 watt laser capable of? How about a link to the one you have and know works. I have been tempted but don't want to waste a lot of time on something that be garbage.
toggle quoted message
Show quoted text
On 1/17/2022 6:34 AM, Chuck Kahler wrote: I will be using the ¡°THC ¨C2¡± Controller from cnc4pc.com
I simply built a quick release adapter to hold my plasma torch on my 15 x 30¡± travel milling machine.
This machine also has a 180 W CO2 laser attached to it, so it¡¯s an all purpose milling, laser cutting, plasma cutting machine for relatively small parts.
-sent from my iphone --
On Jan 17, 2022, at 4:18 AM, o1bigtenor <o1bigtenor@...> wrote:
?On Mon, Jan 17, 2022 at 2:45 AM Chuck Kahler <chuck767@...> wrote:
Thanks for the info, because of other commitments I will not be installing my THC system for about a month, but I will report back To the group on how this set up works. Hmmm - - - which THC system did you install?
Would also be curious as to the actual plasma system your working with.
(I really want a decent sized plasma torch and buying a system from
the big boys is out of reach ($$$$$) - - - so wondering - - - )
TIA
-sent from my iphone --
On Jan 16, 2022, at 10:52 PM, Stan ... <alaska.stan@...> wrote:
?
Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-)
On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler <chuck767@...> wrote:
Thanks Stan,
Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck
-sent from my iphone --
On Jan 16, 2022, at 9:23 PM, Stan ... <alaska.stan@...> wrote: ?
I did... it is a jpg attachment
On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler <chuck767@...> wrote:
Stan,
Would you please post a sample
of your G-code
I would like to compare it to the post processed G code using the Artsoft Plasma post processor.
Thanks,
Chuck
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
?
Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful.
Stan
On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler <chuck767@...> wrote:
Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor?
Chuck
-sent from my iphone --
On Jan 13, 2022, at 11:13 PM, Stan ... <alaska.stan@...> wrote:
?
Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps.
Stan
On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler <chuck767@...> wrote:
I recently attached by plasma torch to my milling machine.
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.
Going this route I am using a lot of consumables on the plasma torch.
I¡¯m interested in using the MACH3 plasma profile With the torch height control, THC, Provisions.
Can someone point me in the right direction to get this set up?
thank you,
Chuck
Attachments:
20220114_122145.jpg
--
Best regards, Spencer Chase
67550 Bell Springs Rd.
Garberville, CA 95542 Postal service only.
Laytonville, CA 95454 UPS only.
Spencer@...
(425) 791-0309
|
Spenser,
On a single pass, I have cut three-quarter inch MDF at 14 in./min. using about 80% laser power.
I can cut 1/4 inch plywood at 40 inches per minute using 80% power.
Search Amazon for RECI W8 150-180W co2 laser for the tube I used.
There are a lot of less expensive tubes out there but the quality is nowhere near RECI quality.
Have fun,
Chuck
toggle quoted message
Show quoted text
-sent from my iphone -- On Jan 17, 2022, at 9:07 AM, spencer@... wrote:
?What is the 180 watt laser capable of? How about a link to the one you have and know works. I have been tempted but don't want to waste a lot of time on something that be garbage.
On 1/17/2022 6:34 AM, Chuck Kahler wrote:
I will be using the ¡°THC ¨C2¡± Controller from cnc4pc.com
I simply built a quick release adapter to hold my plasma torch on my 15 x 30¡± travel milling machine.
This machine also has a 180 W CO2 laser attached to it, so it¡¯s an all purpose milling, laser cutting, plasma cutting machine for relatively small parts.
-sent from my iphone --
On Jan 17, 2022, at 4:18 AM, o1bigtenor <o1bigtenor@...> wrote: ?On Mon, Jan 17, 2022 at 2:45 AM Chuck Kahler <chuck767@...> wrote:
Thanks for the info, because of other commitments I will not be installing my THC system for about a month, but I will report back To the group on how this set up works. Hmmm - - - which THC system did you install?
Would also be curious as to the actual plasma system your working with.
(I really want a decent sized plasma torch and buying a system from
the big boys is out of reach ($$$$$) - - - so wondering - - - )
TIA
-sent from my iphone --
On Jan 16, 2022, at 10:52 PM, Stan ... <alaska.stan@...> wrote:
?
Yes I programmed all that in... any issues and I know right where it is. And it's a great way to learn all the good:-)
On Sun, Jan 16, 2022, 9:26 PM Chuck Kahler <chuck767@...> wrote:
Thanks Stan,
Looks similar to what I get, except my post processor doesn¡¯t show the (Comments)
Chuck
-sent from my iphone --
On Jan 16, 2022, at 9:23 PM, Stan ... <alaska.stan@...> wrote: ?
I did... it is a jpg attachment
On Sun, Jan 16, 2022, 7:53 PM Chuck Kahler <chuck767@...> wrote:
Stan,
Would you please post a sample
of your G-code
I would like to compare it to the post processed G code using the Artsoft Plasma post processor.
Thanks,
Chuck
-sent from my iphone --
On Jan 14, 2022, at 1:24 PM, Stan ... <alaska.stan@...> wrote:
?
Chuck, in my opinion your post processor is at the core of any work done by CNC. I used the MP1000¨C THC for my post processor initially and then edited it for the laser, scribe, plasma, and the oxy acetylene torch that is on the table. I also made descriptions in my output file and put in cut sequence numbers so I can start stop or correct anywhere in a job. I will post a picture of the g code... a proficient working knowledge of Lua is very helpful.
Stan
On Fri, Jan 14, 2022, 6:12 AM Chuck Kahler <chuck767@...> wrote:
Thank you for the detailed response Stan,
Are you using the artsoft Mach3 plasma post processor?
Chuck
-sent from my iphone --
On Jan 13, 2022, at 11:13 PM, Stan ... <alaska.stan@...> wrote:
?
Hello Chuck, I have been using mach3 for many years on my 9' x 23' plasma table and basically what you're trying to do requires that you use a plasma post processor with THC. That is where your THC is going to be initiated in the output G-Code and then ran in the plasma screen set that interact with your THC controller. The other part of the THC is a Plasma Cutter with torch active/ volts or adding this option through the installation of an Amp coil. You need to check with your plasma manufacturer for this option on your model or get one from the manufacturer of your THC controller that you will be using. Hope this helps.
Stan
On Thu, Jan 13, 2022, 2:30 PM Chuck Kahler <chuck767@...> wrote:
I recently attached by plasma torch to my milling machine.
I am using the basic Mill profile And post processing my fusion 360 plasma cutter paths with the MACH3 plasma post processor within fusion 360.
Going this route I am using a lot of consumables on the plasma torch.
I¡¯m interested in using the MACH3 plasma profile With the torch height control, THC, Provisions.
Can someone point me in the right direction to get this set up?
thank you,
Chuck
Attachments:
20220114_122145.jpg
--
Best regards, Spencer Chase
67550 Bell Springs Rd.
Garberville, CA 95542 Postal service only.
Laytonville, CA 95454 UPS only.
Spencer@...
(425) 791-0309
|
