开云体育

was there ever a fix to the bug that causes the displayed jog increment to not necessarily be what it actually is when starting mach4? i am using very expensive router bits now and would be really pissed if i snapped one off because the jog increment showed .01" and it moved an inch instead. i try to remember to reset it each time i start mach4 but i am good at forgetting things and this could cost me $60 or more in one bad move. i jog to edges to set my home position for a piece.

there is a big difference between .01" and 1 " that would be about .99" certainly enough to break a new compression router bit.

Thanks Gary

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

开云体育

I don't think so ... What Rev are you on and what are you doing?

______________________________

Brian Barker
Engineering / Development
ArtSoft | Newfangled Solutions
Livermore Falls, Maine (USA)
Phone: 207(618)1449
Webpage: 

开云体育

version 4.2-0.4612 making wooden stuff. the problem is not with making stuff it is jut the fact that the displayed jog increment shown when mach4 boots is not necessarily what it will move. it pretty mush always shows .01" which was the last used increment but it can move 1 inch instead. i have mentioned this a t least a few times.

I don't think so ... What Rev are you on and what are you doing?

______________________________

Brian Barker
Engineering / Development
ArtSoft | Newfangled Solutions
Livermore Falls, Maine (USA)
Phone: 207(618)1449
Webpage: 

On 12/7/2021 1:00 PM, spencer@... wrote:

was there ever a fix to the bug that causes the displayed jog increment to not necessarily be what it actually is when starting mach4? i am using very expensive router bits now and would be really pissed if i snapped one off because the jog increment showed .01" and it moved an inch instead. i try to remember to reset it each time i start mach4 but i am good at forgetting things and this could cost me $60 or more in one bad move. i jog to edges to set my home position for a piece.

there is a big difference between .01" and 1 " that would be about .99" certainly enough to break a new compression router bit.

Thanks Gary

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

开云体育

I fixed that issue long ago (or so I remember ) I can crank through the SVN logs tomorrow and see what I can find.

Thanks for the rev number

______________________________

Brian Barker

Webpage: 

开云体育

so the current rev is higher than mine? the last time i checked mine was current. any special place to get the new one and do i need to find reg number again or???

I fixed that issue long ago (or so I remember ) I can crank through the SVN logs tomorrow and see what I can find.

Thanks for the rev number

______________________________

Brian Barker

Webpage: 

On 12/7/2021 3:30 PM, spencer@... wrote:

version 4.2-0.4612 making wooden stuff. the problem is not with making stuff it is jut the fact that the displayed jog increment shown when mach4 boots is not necessarily what it will move. it pretty mush always shows .01" which was the last used increment but it can move 1 inch instead. i have mentioned this a t least a few times.

On 12/7/2021 10:50 AM, Brian Barker wrote:

I don't think so ... What Rev are you on and what are you doing?

______________________________

Brian Barker
Engineering / Development
ArtSoft | Newfangled Solutions
Livermore Falls, Maine (USA)
Phone: 207(618)1449
Webpage: 

On 12/7/2021 1:00 PM, spencer@... wrote:

was there ever a fix to the bug that causes the displayed jog increment to not necessarily be what it actually is when starting mach4? i am using very expensive router bits now and would be really pissed if i snapped one off because the jog increment showed .01" and it moved an inch instead. i try to remember to reset it each time i start mach4 but i am good at forgetting things and this could cost me $60 or more in one bad move. i jog to edges to set my home position for a piece.

there is a big difference between .01" and 1 " that would be about .99" certainly enough to break a new compression router bit.

Thanks Gary

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

开云体育

the version on the web site is 4612 and that is what i have and the problem was not fixed as far as I know. i recently tested it but who knows i am getting flaky. pleae check the logs or whatever.

I fixed that issue long ago (or so I remember ) I can crank through the SVN logs tomorrow and see what I can find.

Thanks for the rev number

______________________________

Brian Barker

Webpage: 

On 12/7/2021 3:30 PM, spencer@... wrote:

version 4.2-0.4612 making wooden stuff. the problem is not with making stuff it is jut the fact that the displayed jog increment shown when mach4 boots is not necessarily what it will move. it pretty mush always shows .01" which was the last used increment but it can move 1 inch instead. i have mentioned this a t least a few times.

On 12/7/2021 10:50 AM, Brian Barker wrote:

I don't think so ... What Rev are you on and what are you doing?

______________________________

Brian Barker
Engineering / Development
ArtSoft | Newfangled Solutions
Livermore Falls, Maine (USA)
Phone: 207(618)1449
Webpage: 

On 12/7/2021 1:00 PM, spencer@... wrote:

was there ever a fix to the bug that causes the displayed jog increment to not necessarily be what it actually is when starting mach4? i am using very expensive router bits now and would be really pissed if i snapped one off because the jog increment showed .01" and it moved an inch instead. i try to remember to reset it each time i start mach4 but i am good at forgetting things and this could cost me $60 or more in one bad move. i jog to edges to set my home position for a piece.

there is a big difference between .01" and 1 " that would be about .99" certainly enough to break a new compression router bit.

Thanks Gary

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only

-- 
Spencer Chase
67550 Bell Springs Rd.
Garberville , CA 95542 USPS mail only 
Laytonville, CA 9545 UPS/Fedex only