开云体育

Yes, it can work with an encoder or an index pulse.? Check this out: https://www.cnc4pc.com/blog/post/mach4-lathe-using-the-ethernet-smooth-stepper-and-the-c82-breakout-board

Thank you Steve. That's the information I was looking for. In fact I'm surprised that they are stating 10V for the input supply voltage since even rail to rail op-amps don't quite get to the rail

Well, sort of...... The circuitry works better at 10 or 12 volts, but it will function at 5 volts. The issue is that the output range is limited to between approximately Gnd plus about 0.3 volts and

I realize this isn't completely a MACH question but many MACH users have G540's connected to their systems. The VFD pins are the ones I'm wondering about. The specs say optically isolated PWM. Is this

Nothing that I noticed, but I didn’t really try to find any differences either. Threading (once they finally made it work) was fine with either method. Sent: Thursday, March 16, 2023 6:03 PM To:

Thanks. Did you find any difference in behavior? John Sent: March-16-23 3:01 PM To: [email protected] Subject: Re: [MachCNC] MACH4 and Lathe Spindle encoder I ran Mach4 for years using a single-pulse

I ran Mach4 for years using a single-pulse setup. I only changed to an encoder a few years back Sent: Thursday, March 16, 2023 5:43 PM To: [email protected] Subject: Re: [MachCNC] MACH4 and Lathe

It's just I had a question on how hard to migrate from a MACH3 1 PPR to a MACH4 system and whether mechanical and electrical changes were required to use MACH4 due to a quadrature encoder requirement

It works either way, unless something has changed in the last few years Sent: Thursday, March 16, 2023 5:02 PM To: [email protected] Subject: [MachCNC] MACH4 and Lathe Spindle encoder Can MACH4 Lathe

Can MACH4 Lathe still work with only a 1PPR spindle sensor or does it now require a full quadrature encoder and Index pulse?

I have found that if your computer has trouble letting you use an Arduino comm port rebooting the system fixes it for me. Sent: March 12, 2023 4:23 PM To: [email protected] Subject: Re: [MachCNC]

Yes I veryfied and it is recognized as a Com port (Arduino Tool Kit was already installed). Just tried to change the USB port but still the same, modified the Com3 to Com4 label and still the same...

BTW. The screen shot attachment links are at the bottom of my posting. Sent: March-12-23 1:34 PM To: [email protected] Subject: Re: [MachCNC] Mach3 Modbus/Win10 problem For example. I took a fairly

For example. I took a fairly new WIN-10 system that had been upgraded from WIN-7. Even has MACH3 on it although I don't use it. I plugged in an ESP32 DevKit1 and came up with the screen that shows

Ok.? Bring up the device manager and see if the aeduino shows up as a serial port or under USB devices as unknown.If unknown you can try installing the Arduino IDE which will likely install the

This is just a USB arduino connection...

How are you connecting to the MODBus? A USB dongle that acts as a serial port or a physical serial port? After WIN-7 Microsoft disallowed most USB PID combinations unless the owners paid $5k or so for

Hi, Trying to move my Mach3/Ess from Win XP to Win10, I get an "Error triggered" "Art Code 1" and "Art Code 9991" at the startup. If I create a new profile by cloning my working profile, everything

I did that on my lathe. I couldn't work out why the finish was so bad. :) Cheers, Peter -- ----------------------------------------------------------------------------- Web

Nevermind. I forgot that I wired in a switch a few years ago. Doh! Sent from Mail for Windows Sent: Friday, March 3, 2023 10:03 PM To: [email protected] Subject: [MachCNC] Forgot how to change spindle