开云体育

I think it's useful to add, once again, that Helmut is not affiliated, in any way, with Linear, or Mike, nor is it this group, for that matter. -- Vlad ______________________ ltspicegoodies.ltwiki.org

Hello PhB. The team was in SwcadIII menu. Activate this command was issued table (form) to enter the input voltage and load current. By entering the data you need and activated, you will get a table

Hello Bordodynov You wrote : " Old SwcadIII had the opportunity to build the circuit on the input requirements for DC / DC. " I don't see what you mean to say about this possibility ( in SwcadIII and

Hello Andy. I am with you a little bit do not agree. Old SwcadIII had the opportunity to build the circuit on the input requirements for DC / DC. Recently, I studied my old files on CDs and found that

Hello Steve You wrote : " With (2) and (3) LTspice points me to a problem that doesn’t exist and not to where the problem does exist. " A/ You are wrong for case (2) [ mixed Qd44 and 2sc ]. There is

Hello Steve You wrote : " With (2) and (3) LTspice points me to a problem that doesn’t exist and not to where the problem does exist. " A/ You are wrong for case (2) [ mixed Qd44 and 2sc ]. There is

such a little thing, such a big error, good going!!!keep teaching, greatly appreciated Thank you, Jeff

Hello, My example hadn't worked with XVII86.exe. Now after the latest update it works. Have you updated it yesterday? Please update. Tools -> Sync Relase Best regards, Helmut

Ok I see that in the log. But I don’t get prompted with any error for which I must “press ok to continue…” which would lead me to look at the log in the first place. Fine… so (1) there’s

Hello Jeff, The attribute "value" in LM358Dual.asy has to be LM358DUAL and not LM358. Unzip my example in a new folder and run it. lm358dual1.zip

Jeff asked about a "Pin count mismatch error" with a dual LM358 symbol. In your symbol attributes, the Value attribute is "LM358". This means LTspice will try to use the "LM358" subcircuit. Change it

I tried to use the info you taught me on the LM393A dip14 project to make the LM358 dip8 project and I just can't find why it won run, please take a look at it and let me know what's wrong, Thanks,

Hello With all Qd44vh10 replaced If I replace .endL by .ends I get no error or warning. If I keep .endL I get : Error on line 1138 : .endl 2sc6144sg Unknown control card Error on line 1138 : .endl

It looks very much as though your model isn't called *exactly* ' Qd44vh10'. There could be a leading or trailing space or another invisible character. Have you ever uploaded the model? With best

Philippe Replace all 6 of the Qd44vh10 with 2SC6144SG and tell me if you get an error. I get none. If one Qd44vh10 remains then yes I get an error. Regards Steve

TINA-TI always was a reduced-capability version of the full TINA program (which Texas Instruments did not create). TINA never was free, as far as I know. TINA-TI was always free. Andy ?

Gunoi Nare wrote: "Check out TIs TINA.It is no more free but the older version (XPs) is still good enough for me. And it WAS FREE." It still is! http://www.ti.com/tool/tina-ti You're wrong that it is

andrew.lohmann wrote: "Since ADI took over of LT I had a look at ADI's simulator but it is not compatible with XP ..." If you mean their ADIsimPE, I think you mostly don't need to use it. So why

Hello Steve "If there is any instance of Q44dvh10, then LTspice tells me I have a problem with the lack of a model statement for Q44dvh10 - even though I clearly have one. LTspice does not ever tell

The free TINA is severely restricted/handicapped. You can not save, print etc files.try it!G To: LTspice@... Sent: Wednesday, August 10, 2016 7:35 AM Subject: Re: [LTspice] Re: No XP? ?