¿ªÔÆÌåÓý

Date
Re: A three Phase question please
In message <1387825178.9799.YahooMailNeo@...>, dated Mon, 23 Dec 2013, kim nielsen <dkkiboni@...> writes: 4 mm x 9 mm, about USD0.25 50-off. Those are checked for
By John Woodgate <jmw@...> · #68811 ·
Re: A three Phase question please
Hi John Maybe a resistor across etch diode, but I think it is not necessary, the leakage current is big enough to balance the voltage across the diodes. Have used about 100,000 diode without resistor
By kim nielsen · #68810 ·
Re: A three Phase question please
In message <DUB110-W214CEC96F96D0814B332F3ACC10@...>, dated Mon, 23 Dec 2013, Michael Peter <michael883575@...> writes: In real life, use two wattmeters. Call the phases A, B and C. One
By John Woodgate <jmw@...> · #68809 ·
Re: A three Phase question please
Measuring 3-Phase power is exactly the same as measuring single-phase power, except you have to do it 3 times. In practice you need a measurement set-up that monitors the vectorial product of voltage
By Jerry Lee Marcel · #68808 ·
Re: A three Phase question please
While following this thread, it just dawned on me that I do not know how to measure 3 phase power. Any suggestions how to do this in real life and ofcourse in LTspice as well. Michael To:
By Michael Peter Kiwanuka · #68807 ·
Re: CIC unstable output
Hello John I wish the wealth of information that can be found over the Internet could let me know about the exact nature of the problem LTspice shows for this particular schematic. Thinking of sparing
By Vlad · #68806 ·
UC1845A SPICE model?
Hi, Does anyone have a UC1845A SPICE model they can share? Ken
By ken_and_wanda · #68805 ·
Re: CIC unstable output
This is from my phone, so it may be abreviated and spelled poorly. Perhaps the problem is that the analog nature of the delay lines allows small errors to grow due to the very high gain. Maybe
By analog spiceman · #68804 ·
Re: JFET Model
That was easy thanks. Chris
By Chris Maness · #68803 ·
Re: JFET Model
Hello Chris, Place a "njf" on the schematic. Right-mouse click on it and take a model from the list. Best regards, Helmut
By Helmut Sennewald · #68802 ·
JFET Model
I am interested in building a pierce oscillator with a JFET to simulate the way a vacuum tube would behave in a pierce oscillator, but I don't see any JFET devices in the components section. Any
By Chris Maness · #68801 ·
Re: CIC unstable output
Hello, Vlad - I have always found it challenging to translate discrete digital filters back into the analog for simulation. It is very easy to make errors that are not obvious but which completely
By Jim Wagner · #68800 ·
Re: CIC unstable output
In message <l97cr5+1isqo3s@...>, dated Sun, 22 Dec 2013, imbvlad@... writes: I realise that, if you are referring to my comments about the results of a Google search. It is certainly
By John Woodgate <jmw@...> · #68799 ·
Re: CIC unstable output
Thank you for the directions, but I wouldn't have started something if I didn't have at least one clue about it :-) It's true that I can't say I'm an "expert", but I'll manage, somehow. The problem,
By Vlad · #68798 ·
Re: CIC unstable output
In message <l97732+1panslk@...>, dated Sun, 22 Dec 2013, imbvlad@... writes: There is a lot of information disclosed by a Google search for CIC filter, but I don't claim to
By John Woodgate <jmw@...> · #68797 ·
Re: CIC unstable output
If you say so. Being no expert either (by far), here's what I know, in short: they're a cheaper approach to interpolators/decimators because they're multiplier-free (not that it would matter in
By Vlad · #68796 ·
Re: A three Phase question please
In message <1387726122.76180.YahooMailNeo@...>, dated Sun, 22 Dec 2013, kim nielsen <dkkiboni@...> writes: Even so, I would put 1 meg resistors **rated for 1000 V at
By John Woodgate <jmw@...> · #68795 ·
Re: A three Phase question please
Use UF4007(SF4007), they are 1A, 1000V, 75nS Trr and cheap. 1n4148 have only 75volt reveres voltage. 10pcs. in series gives 10KV. I would use 11 to have som margen. The biggest problem with this kinds
By kim nielsen · #68794 ·
Re: Sub ckt
---In LTspice@..., <zardos49@...> wrote: Thanks Helmut ! I had the files scattered and it could not find them. Sent from my BlackBerry? by Boost Mobile Don't scatter files! Don't put any
By schockenbaum · #68793 ·
Re: CIC unstable output
Vlad asked: "At least does anyone know why the samples lose their constant-time values?" I think what you're asking is, why does the waveshape appear to lose its staircase appearance. Well it still is
By Andy I · #68792 ·