Re: Monte Carlo of stepped voltage
#Monte-Carlo
Tony, Understand the .step and .param are Spice directives but where does the "V1 OUT 0 {Perturb}" go.? Is that the DC value for the V1 supply?? Also do you run this as a transient analysis, DC
By
larryg
·
#157204
·
|
Re: AC Voltage Stabilizer update
Yeah, adjacent key typo¡ Sent: Thursday, January 02, 2025 9:52 AM To: [email protected] Subject: EXTERNAL: Re: [LTspice] AV Voltage Stabilizer update Dave, I'm just curious - The Subject line is "AV
By
Bell, Dave
·
#157203
·
|
Re: Current source TBL function
Hi all, I'm a bit late to this discussion but I came across the? current "TBL" function too and wasn't really sure what it meant and like the initial poster didn't find a satisfactory answer in
By
abruin@...
·
#157202
·
|
Re: AC Voltage Stabilizer update
Dave, I'm just curious - The Subject line is "AV Voltage Stabilizer update". What is the "AV" about? Is it supposed to be "AC"? Andy
By
Andy I
·
#157201
·
|
Re: LM324 based automatic voltage stabilizer circuit simulation
Hi, Hasan, Just getting around to looking at your uploaded circuit. The Relay Driver subcircuit already incorporates all of the external components to the left of each on, the input diodes,
By
Bell, Dave
·
#157200
·
|
Re: AC Voltage Stabilizer update
Add a .STEP command, where you step a parameter representing the four voltages.? Then use that parameter to control the voltage source's magnitude. *Note* that Dave's schematic STILL has the mistake
By
Andy I
·
#157199
·
|
Re: AC Voltage Stabilizer update
Remember to always include the symbols and models used that did not come with LTspice. Don't think that you do not need to because it is in the latest directory on your computer's drive, or because
By
Andy I
·
#157198
·
|
Re: AC Voltage Stabilizer update
More tomorrow, but . . . 1. You need a .param statement to assign a value to ¡°wp¡±, a wiper position for the pots inside the relay drivers. See below 2. R11 has no assigned value 3. D11, 12, and 13
By
Bell, Dave
·
#157197
·
|
Re: AC Voltage Stabilizer update
Dave, Thank you a lot for making such clean simulation circuit.You can remove the transistor switching relay part but perhaps it has been made for getting protection in real case.I understand why you
By
MD MUBDIUL HASAN
·
#157196
·
|
Re: DTMF keypad design
A schematic for the original BELL single transistor DTMF generator can be found here: https://www.repeater-builder.com/tech-info/dtmf/bell-dtmf.html Ray WB6TPU
By
Ray Anderson
·
#157195
·
|
Re: AC Voltage Stabilizer update
New update to the modified AC Stabilizer circuit: Fixed the output relay, I believe. Replaced the driver circuit with a NO relay only. Dave Sent: Wednesday, January 01, 2025 5:20 PM To:
By
Bell, Dave
·
#157193
·
|
AC Voltage Stabilizer update
Hasan, please see the new file I just uploaded. Cleaned up the three relay driver circuits pn the left side. I'm not sure if the driver in the upper-right will work there; the inputs are different,
By
Bell, Dave
·
#157191
·
|
Re: Monte Carlo of stepped voltage
#Monte-Carlo
Sorry, I realised that I didn't quite get that right - the perturbation is proportional to Vmc. This fixes it: .step param Vmc 0 10 1 .param Perturb mc(1,0.05)+Vmc-1 -- Regards, Tony
By
Tony Casey
·
#157190
·
|
Re: LM324 based automatic voltage stabilizer circuit simulation
If you have never changed your default font size, then you do not need to change it back to the default size. The default font size is in LTspice's Control Panel (settings).? It is the toolbar button
By
MD MUBDIUL HASAN
·
#157189
·
|
Re: Making 4 bit Flash ADC using Priority encoder
I uploaded "ADC Flash AI1.asc" which has some things fixed. * I removed the short-circuit that was across V2. * I removed the short-circuit that was across Vin. * I changed Vin so that it sweeps over
By
Andy I
·
#157188
·
|
Re: DTMF keypad design
Not surprisingky, I've never seen that design. ------------------------ DavD KC0WJN ------------------------ [email protected]> wrote:
By
Dave Daniel
·
#157186
·
|
Re: LM324 based automatic voltage stabilizer circuit simulation
The default font size is in LTspice's Control Panel (settings).? It is the toolbar button with the hammer icon. Then click on the tab for "Drafting Options". If you have never changed your default
By
Andy I
·
#157185
·
|
Re: LM324 based automatic voltage stabilizer circuit simulation
This is the link where Mr. Dave has uploaded the part,?/g/LTspice/files/Temp/relay_driver.zip
By
MD MUBDIUL HASAN
·
#157184
·
|
Re: LM324 based automatic voltage stabilizer circuit simulation
Thank you @andy to take part here.? 1. LM324 lib is absent ! You may not need an LM324 model.? The LM324 is an op-amp.? You can probably use UniversalOpamp2 which is in LTspice.>>Yes, I can see,
By
MD MUBDIUL HASAN
·
#157183
·
|
Re: LM324 based automatic voltage stabilizer circuit simulation
Indeed! Major difference at 28 B. I see why it looked terrible. I¡¯ll see if I can ¡°tolerate¡± it there¡ Dave Sent: Wednesday, January 01, 2025 9:54 AM To: [email protected] Subject: EXTERNAL:
By
Bell, Dave
·
#157182
·
|