开云体育

Hello Patrick, Your subcircuit was wrong. The correct syntax for your subcircuit should be as shown below. Compare every line to see what I have changed. *Pinbelegung *Pin 1: Input *Pin 2: Output *Pin

OK, thanks Helmut, Now I can get it to work at least, but it still seems awkward to use: I have to 1) Un-tick "Sync Horiz. axis". 2) Set Manual Limits 3) Re-tick "Sync Horiz. axis" (So, not what I'd

Patrick asked: "1) When I want to simulate the circuit I get the error "Analysis failed matrix is singular" ? ? Where does it come from and how can I prevent it except the option to switch a

Hallo all together, I want to make an AC - simulation of a Boost Converter by its Laplace transfer function. For that I have designed a subcircuit Boost.sub , a symbol Boost.asy and a circuit

In message <lm20sr+1jfqvok@...>, dated Tue, 27 May 2014, "basier.philippe@... [LTspice]" <LTspice@...> writes: But did you submit your 'wish list' for something

Hello all of you As I live in Paris I phoned to "Lycée Richelieu". It's a Yahoo or i-phone problem. I think i-phone. Not fishing or attack problem. So: there will be no more rubbish mail. Regards PhB

The end with the "dot" does make a difference. If you rotated or mirrored an inductor on the LTspice schematic so that the "dot" swapped locations with respect to the rest of the circuit, that would

hitec92407 wrote: "I was able to get the macro model working." Excellent. "... There actually is a ground input on the schematic." "Its Pin 12 shown in the BIAS section. All ground points on the

Mike wrote: "IC=-100.8u "I understand this is to establish an initial current. But how do we know which circuit it applies to, and how do we tell it is intended to set the current in L1?" We know it's

Dear Helmut, I thiink you uploaded this file so I'm sending the question to you. In crystal.asc, located at

Friends I dont know who is sender of above message ( thats caused misunderstanding) , but i am wondered how it addede to my querry. Sorry from my side for inconvinience. But i am not responsible for

I can see it, too, unfortunately. Vlad ______________________ ltspicegoodies.ltwiki.org -- holding, among others: a universal analog/digital filter, block-level models for power electronics (and not

I got it also. It (at least superficially) appears to be sent via the group: ================================================================ From: motauakil@... [LTspice]

Hello John, It looks like you got this message personally, because I don't see it in the group messages. :-) Best regards, Helmut

In message <psbkcu5qegym7hw3xd4yqhh2.1401115279761@...>, dated Mon, 26 May 2014, "motauakil@... [LTspice]" <LTspice@...> writes: Who approved this rubbish? I hope the

Thanks alot Rick and Helmut for reply..Now i am Ok with the simulation timing :)

In message <CAK-wn_4VATz=nfQ0uy+hDJTvqE2M2fqVdhLesuQoksSN_x9STA@...>, dated Mon, 26 May 2014, "Sam Jesse revrvr@... [LTspice]" <LTspice@...> writes: The orientation in the

Hi The point which I was most concerned about is the fact that L3 is "rotated" unlike L1 and L2. Thank you <LTspice@...> wrote:

In message <CAK-wn_6=bn+xLOd_mBp9qofHnHq+39rP=WLhM8V0BH5DLuJ+XA@...>, dated Mon, 26 May 2014, "Sam Jesse revrvr@... [LTspice]" <LTspice@...> writes: That is a VERY big

Hello, This circuit is simulated with acceptable speed when using the Alternate solver. Control Panel -> Solver:Alternate Best regards, Helmut