开云体育

I should add I completely re-capped it using the Hayseed Hamfest kit, and changed about 12 resistors that were off-spec.

Thanks for this info. I will add the panel fuse holder, so that the fuse can be changed without taking the radio apart. I am not too concerned about changing its original look. You won't see the fuse

I think your relay is ok. I believe your problem is on the grid side of V20B. I would not "tinker" with the values. Between the HT44, cyclone, cycloneII and the cycloneIII this same basic circuit is

Happy new year Jim, Check the static condition of V20A/B per chart below. [cid:6e8199ab-db41-41ba-9f91-7ba381860ca9] Walt Cates, WD0GOF https://wd0gof.com/Hallicrafters Your past has no control over

Greetings to the Group: I am trying to put the finishing touches on an SR-400 Cyclone transceiver.?? I have run into a problem with the VOX, however.?? The Vox Delay when set to minimum is about 1

On Sat, Jan 7, 2023 at 06:08 PM, Jim Pruitt wrote: > > What tips does the Edsyn 951 use?? I have one new in the box that I bought > about 15 years ago but never even opened the box.? I have up until

Hello Mike. What tips does the Edsyn 951 use?? I have one new in the box that I bought about 15 years ago but never even opened the box.? I have up until recently always used my Weller WTCPT and

WE1010NA WE1/WEP70/PH70 SOLDERSTAT.120V https://a.co/d/cApgdWm Sent from Proton Mail for iOS

The Hakko is a vacuum desoldering gun. That’s it’s only purpose. It has a pump built in. Sent from Proton Mail for iOS

Steve said ? "The stock tip that comes with it works well for boat anchors. " , thats what i wanted to know, but he didn't say if it comes with a vac pump?? PS I AM JUST MUCKING ABOUT WITH the editor

Dan, I have had the Hakko 808, the predecessor to the 300/301, for years. I've used it on everything from BA rigs to PCBs. It works well on chassis itesm you mentioned as well as removing components

Yes. I’ve used the Hakko for restoration work on many boat anchors. And still do. Sent from Proton Mail for iOS

?Does this Hakko work OK desoldering point-to-point wiring, tube sockets, and terminal strips, like in BA radios? My never-used-one impression is they tend to work best on PC boards, etc., no? I've

I use a Hakko 301 desoldering gun and it’s the cat’s meow. A variety of tips are available. The stock tip that comes with it works well for boat anchors. 73 - Steve, KW4H Sent from Proton Mail for

Tom , hi again. I would like a good motorized vacuum sucker station with an iron able do old anchors, and if possible newer smaller stuff. It seems, these days ,the thermal mass of the tip is not

Hi Craig, Ken ,and the gang I was reluctant to suggest the use of a fuse holder within the radio; and what kind and how and where to mount it, and then Ken provided one option. I have wrestled with

Don, Good point....I have an OLD Weller dual wattage gun that I think Ben Franklin used for his electricity experiments....hahahaha ..... and think it's too clunky and hot to use on circuits.....I

Hey Tom, I have a similar question, but I wonder if a prime criteria isn’t whether it is for old tube etc stuff and using 60/40 AND/OR for new PCBs and hi temp leadless solder? My guess is that it

Check out auctions for the assets of tech businesses that are shutting down. For some reason things like soldering stations sell cheaper there than on eBay. I got a wonderful HAAKO soldering station

I’ve been soldering wires since I was a teenage novice ham back in 1957 followed by a lengthy career in broadcast engineering. The Edsyn Loner (model 951SX) is the best I’ve found in all these