开云体育

+ AA6YQ comments below + Thanks, but I looked downloaded that manual from the Yaesu web page yesterday: it doesn't include documentation of the radio's CAT instruction set. 73, Dave, AA6YQ

English manual for the Yaesu FTX-! Series available here: https://www.wimo.com/en/yaesu-ftx-1-field-optima?srsltid=AfmBOoqXNZ5IJ9M_4gkiUQLD9PVe0z_4iqlPnnd6m_hXrGw4l7vaKCZ3#?1207=25920 I just

Others have reportedly downloaded a pdf but it is currently unavailable:

+ AA6YQ comments below Sent: Sunday, May 25, 2025 4:40 PM To: [email protected] Subject: Re: [DXLab] TQSL on a new build isn't uploading In the actual QSO the myQTH is Bakersfield In the myQTH Tab

In the actual QSO the myQTH is Bakersfield In the myQTH Tab it’s Bakersfield In the QSO tab it’s Bakersfield in the LoTW operation window In TQSL it’s Bakersfield I just tried uploading again

+ AA6YQ comments below + The error message states that the QSO specifies a QTHID of "bakersfield" - note the lower case b - that specifies an LoTW Station Location of "Home". Have you defined a myQTH

I'm getting the message: Disabled QSL Queue entry for JH8ISO on 2025-05-25 at 13:04:38 - station location "Home" specified in QSO's QTHID item "bakersfield" doesn't match station location

In DXKeeper, check the "Config" button. Then "QSL Config" on the lower left corner. In the "DXKeeper QSL Configuration" window, select the "LoTW" tab. What is the "TQSL" area labeled? (Mine says "TQSL

Every time DXLab Suite starts, I get the message "A new TQSL (V2.8.1) is available". I am already running that version. Any suggstions as to how to address this? Thanks, Roger EI8KN.

Will do, thanks!

There is no CAT instruction set info in any of the documentation at: <https://yaesu.com/product-detail.aspx?Model=FTX-1%20Series&CatName=HF%20Transceivers/Amplifiers> 73, ... Joe, W4TV

+ AA6YQ comments below + From what URL can I download documentation for this radio's CAT instruction set? 73, Dave, AA6YQ

The referenced yaesu link shows: "We are pleased to introduce the new FTX-1F and FTX-1Optima" "FTX-1Field is a Portable 6W or 10W* HF/50MHz/VHF/UHF Multimode Transceiver. (*10w with 13.8VDC supply.)"

+ AA6YQ comments below will dxlab support the new ftx-1? + I can't find any information about the FTX-1 on Yaesu's web site: https://www.yaesu.com/ + My understanding is that FTX-1 is a receiver that

+ AA6YQ comments below My transceiver is an IC7300. I am on FT8 with WSJT. A CW DX spot comes out, and I double-click in spot collector. Commander changes to the correct frequency, mode, and filter

I have observed this behavior while never noticing it before. My transceiver is an IC7300.? I am on FT8 with WSJT.? A CW DX spot comes out, and I double-click in spot collector.? Commander changes

+ AA6YQ comments below When I post to the Cluster (using SpotCollector) the audio alarm readout says "Grid Square FO93" included in the announcement. First of all: 1. F093 is wrong, and no matter what

will dxlab support the new ftx-1? thanks Reggie k6xr

When I post to the Cluster (using SpotCollector) the audio alarm readout says "Grid Square FO93" included in the announcement. First of all: 1. F093 is wrong, and no matter what Call is Spotted, the

+ AA6YQ comments below. You'd have to account for the fact that some parks are in multiple counties, states, and even grids. + The downloadable POTA park definition file specifies the following for