开云体育

What are your other CAT parameters set at? Normally a quad core processor (or better) and at least 8GB RAM. I run it on an older Quad Core (AMD A8-3850 APU 2.90 GHz) with 12 GB RAM & 2 TB H/D with no

Hi DaveI have 2 qth and 2 similar setups with 2 icom 7300 and 2 (Almost) similar win 7 pc.In my qth1 i have dxlab installed and running perfectly, with the commander waterfall? running smoothly at

If this proves to be a reoccurring problem I will reach out to ARRL LOTW group. If it has happened before it would have been some QSO that was of no consequence to my DXCC totals. I likely would not

Dave That fixed it. thank you. 73 Tim VE6SH

+ AA6YQ comments below Just today, the SC window remains minimized in the system tray (running Win 10). Usually the three windows for the spot sources run minimized but the main display opens on the

+ AA6YQ comments below I might have missed it in my searching but does Commander have configurable band edge warnings? + Yes. See

+ AA6YQ comments below It is Avery 94202 1"x4". Also tried blank and also the default # (can not recall it right now). The results seem identical no matter what settings I use. the colums are too

+ AA6YQ comments below Yes I did invoke the sync after the contact was uploaded and it was not marked as confirmed in DXKeeper log. + If the first QSO was logged in DXKeeper with a mode of FT8 and

+ AA6YQ comments below I have SDR waterfalls working for my cheap $7 SDR and for another guy who as the more expensive SDR 2. What I liked about the one waterfall I saw for DXLab was there were

Dave … tnx … Font size was problem. john Sent from Mail<https://go.microsoft.com/fwlink/?LinkId=550986> for Windows 10 ________________________________ Sent: Saturday, March 23, 2019 12:21:40 PM

Just today, the SC window remains minimized in the system tray (running Win 10). Usually the three windows for the spot sources run minimized but the main display opens on the screen. ? I have tried

I might have missed it in my searching but?does Commander have configurable band edge warnings?

It is Avery 94202 1”x4”. Also tried blank and also the default # (can not recall it right now). The results seem identical no matter what settings I use… the colums are too small and the info

Need to purchase Win4Yaesu Suite $60.00 USD to run N1MM for the FT-991A. Jerry N7YGE Sent: Saturday, March 23, 2019 3:57 AM To: [email protected] Subject: Re: [DXLab] Waterfall for Yeasu FT-991A For

This sounds great! I'm new to SDR (don't have one yet) but I'm thinking about purchasing the SDRPlay RSP1a and doing?the RXout?mod on my TT OMNI-VII. Then I'll?see about integrating Commander,

Yes I did invoke the sync after the contact was uploaded and it was not marked as confirmed in DXKeeper log. After I uploaded the ADIF from WSJT log using TQSL and did the sync that QSO was mark

For contest operation, N1MM supports a spectrum display with superimposed callsigns from the packet spots. You can see and read about it here:

I have SDR waterfalls working for my cheap $7 SDR and for another guy who as the more expensive SDR 2. What I liked about the one waterfall I saw for DXLab was there were callsigns showing. I have not

* More AA6YQ comments below To unmute the soundcard (well, one of several, but this is how I did it under Windows 10: Strike the Windows key, type "sound". The first item was "Sound: Control Panel"

+ AA6YQ comments below I have tried for days to print qsl labels. I think I have read everything several times. Problem is when I print, the characters are on top of each other and I can not figure