开云体育

I wonder if you have a temperature related continuity problem with the Teensy pins rather than a processor problem.? I don't have a fan on my v11 and the processor runs without problem at mid-40s.

Nice find, when I got drugged kicking into Microwave builds I latched onto a nice HP SG 2-13 GHZ. Has been instrumental in setting up MW horns and such. I use TG in SA but I don't trust it as I would

I am using Justin's metal case with a decent size Noctura fan. The venting is minimal. I notice if the temp display gets much over 40C the processor will hang up. With top off I see around 36-37

Yep… 10-4 Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand Piton

It will only be 18dB when loaded by 50Ω resistive on both ends.? Other terminations will yield different results. 73, Don N2VGU

The holes, as long as their circumference is less than λ/4, will not affect the shielding properties. Compare the holes in your microwave oven door, which operates at 2450MHz without leakage, to

Oh I have others. but nothing this fancy (or expensive. It cost more than my best SA). My Rigol only goes to 100 MHZ. Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ

You'll be suprised how often you use it. I have an anritsu mg3631a. It one of my most used pieces of equipment. Get Outlook for Android<https://aka.ms/AAb9ysg> ________________________________ Sent:

One of the items I picked up at Hamvention a couple of weeks ago is a new signal generator. Rhode and Schwarz SML01. Its 9Khz to 1.1Ghz and is calibrated to -140 db. In two weeks I'm going to start

Yes try a LPF… Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC Staunton, Illinois Owner – Operator Villa Grand

Friends Thanks for the input on the 20 W amp waveform distortion. After some trial and error I finally came up with a 56 ohm / 430 ohm / 56 ohm Pad attenuator that yielded the following waveform and a

I don't see any problem. Many of us are using 3D printed cases, which offer no shielding whatsoever. Just clean it off and give it a good paint job. I built a linear in a wraparound cabinet originally

I'm curious what your thoughts are for vented cases for the T41. I have a case from a non functional? Swan 500cx HF transceiver. Every side but the front panel has the 3.75mm round holes. I could 3d

I just ordered a single prototype order of 5 PCBs from PCBWay.? The prices are almost back to normal, $29 with shipping.? $1 more than what I have been paying for the past few years. I hope it stays

Mine looked similar to this dave, n3ds

But look at how resilient the PA is… when you over-drive it… its doesn’t blow up… it just goes into compression and “flat tops” like you would want it to… like an audio amp when you are

Got it. Distortion. Thanks Bill

Ah yes, you are over-driving the 20W PA… you need a larger PAD. Dr. William J. Schmidt - K9HZ J62K(J68HZ) 8P6HK ZF2HZ PJ4/K9HZ VP5/K9HZ PJ2/K9HZ VP2EHZ Owner - Operator Big Signal Ranch – K9ZC

attached

As long as its consistent... it should not matter... I designed the LPF for this set (which is the Kenwood/ Elecraft/ Yaesu/ etc. standard): But somehow that got twisted. These standards are important