Keyboard Shortcuts
Likes
- 7x12MiniLathe
- Messages
Search
Re: LittleMachines DROs and dials
Peter Way 10:40am? ? Edited 10:41am I have a Littlemachines lathe with really awful DROs. They use V389 batteries that last about a minute. I have the following questions: 1. I'm working on a 3D printed battery holder that allows a AAA battery instead. Is anyone else interested in theseBad news You buy AAA battery holders from Amazon and Walmart for under package of 4 to 6 $10.00. Some have a on off switch? |
Re: LittleMachines DROs and dials
They had some like for BP mills in the 1960's.?
They did nothing for screw wear in center or nut wear.? FYI If try adjusting nut wear it would not work because of screw wear.? Next travel dial They like to skip.? I think travel dial could work with a using a rake . I use dial indicators. I have one 2" stroke most time I use 1" stroke works.? On the mark every time. Dave? |
Re: Variable speed motors
I have one of his motor/controller running my MicroMark 7x16. The original motor died...feels like one of the magnets dropped out of position. I selected his bare-bones 900W version. Fairly easy to install. I needed to move four holes on the lathe's mounting plate, thank the Lord for the DRO on my mill.? I also had to enlarge the hole on the lower pulley.? That was a challenge reaming it by hand using the un-powered lathe.? Here's a picture of my setup.
Regards, Ray |
Re: LittleMachines DROs and dials
¿ªÔÆÌåÓý??? They don't turn odd when ya hit he switch , they just go to sleep . getting a switch between the batteries & the caliper someway will way improve battery life . animal On 2/19/24 11:08 AM, Bruce J wrote:
|
Re: LittleMachines DROs and dials
¿ªÔÆÌåÓý
--? Bruce Johnson "Wherever you go, there you are." B. Banzai, PhD |
Re: $1000 Budget: Which 7 x 14 to buy?
I would just be careful not to spring for DROs on the dials.? ?I'm regretting that I bought the LMS machine many years ago with awful DROs.? The chewed batteries.? ?They may be better now.? If I were to do it again, I'd save money by getting mechanical dials and then upgrading to linear DROs if needed.
|
LittleMachines DROs and dials
I have a Littlemachines lathe with really awful DROs.? ?They use V389 batteries that last about a minute.? ?I have the following questions:
1. I'm working on a 3D printed battery holder that allows a AAA battery instead.? Is anyone else interested in these? 2. As I researched this, I realized that some of you have found linear DROs that may even be better to position the carriage and cross slide. Can you recommend the best option?? It looks like magnetic ones are good for this application, and some cheap Chinese ones are really capacitive, and not as good.?? 3. Have any of you converted from DROs to old fashioned dial handles?? That would be nice in addition, since those don't require any batteries, etc.? I kick myself every time I think about having bought the DRO version. |
Re: making Colchester Lathes
I think many on this list already know this, but when they say a "5 inch" lathe in the video that refers to the radius that will clear the bed.? Some parts of the world use radius.? Others, such as in the U.S., use diameter.? So, the mini lathe might be 7 inch swing (diameter) or 3 1/2 inch swing (radius) depending on where you are. Charles E. "Chuck" Kinzer
On Monday, February 19, 2024 at 07:51:48 AM PST, davesmith1800 <davesmith1@...> wrote:
A lot labor in just casting.? Dave? |
Re: Variable speed motors
I think he's also on ebay as thecustomcrafter
toggle quoted message
Show quoted text
On Monday, February 19th, 2024 at 9:22 AM, WAM <ajawam2@...> wrote:
|
Re: Variable speed motors
Great find.? Thank you for sharing that.
toggle quoted message
Show quoted text
On 2/19/2024 9:13 AM, Jay Fougere wrote:
Sorry to bump an older thread but in doing some research on the controller board used in the sewing machine motor kit I had purchased I found the following site. |
Re: Variable speed motors
¿ªÔÆÌåÓýSorry to bump an older thread but in doing some research on the
controller board used in the sewing machine motor kit I had
purchased I found the following site. Please note that I have no affiliation to this site nor have any
experience with his products, but he seems to offer a full line of
conversion kits and parts for these motors. This includes full
kits for the mini-lathes and mini-mils along with a ton of other
machines.? It also appears he does some repair services as well. -Jay On 2/9/24 21:45, Tony Smith wrote:
-- -Jay Fougere |
Re: Linear Digital Readout Scales
[Default] On Thu, 15 Feb 2024 18:48:59 -0800, "mike allen"
<animal@...> wrote: at least ya can walk into a Harbor if theres a issue .When adapting a calipers to become a DRO, you'll probably want to drill holes in it and even cut off the jaws. I suspect HF are not going to to very forthcoming when you show up with that hacked-up calipers to claim warranty. -- Helge |
Re: Armstrong threading tool (was "[LL] Lantern toolpost dimensions")
Bill Williams Feb 17? ? My attempt to mll down an Armstrong tool holder ended in blunting the inserts in a carbide face mill! Be forewarned. Bill in Boulder FYI? Using carbide is not best at times for milling hard steel like the Armstrong tool holders.? If trying to mill hard steel use grade C5. They not as hard like grade C2 and brittle.? I found HSS tool bits does better job but not fast like carbide.? Dave? |
Re: Armstrong threading tool (was "[LL] Lantern toolpost dimensions")
Bill Williams Feb 17? ? My attempt to mll down an Armstrong tool holder ended in blunting the inserts in a carbide face mill! Be forewarnedTo cut that steel I think 1060 . You slow speed and HSS will work. Use dark cutting oil.? Brush lots of oil as you cut.? Dave? |
Re: Armstrong threading tool (was "[LL] Lantern toolpost dimensions")
Strangely enough that's how I got my Armstrong knurling tool to fiit in my square turret!? ?Bill On Sat, Feb 17, 2024 at 1:04?PM Miket_NYC <mctaglieri@...> wrote:
|